Stainless Steel Circular Arc Angle Corner Protective

Description

Compared with the laying of floor tiles, the laying of wall tiles requires more technology and some related details. In addition to leaving seams, the laying of wall tiles cannot be empty, and the edge treatment of wall tiles is also critical. Generally, when the wall tiles are laid, they will touch the corners of the wall. There are basically two solutions to this problem. The first is to chamfer directly with wall tiles; the second is to use tile edging strips.

Chamfered edge: Chamfered edge, also known as shoulder, is a more traditional method of processing outer corners, that is, two tiles are processed into a 45-degree angle for seamless or micro-seam connection. It seems simple, but it is a test of the craftsmanship of the construction workers.

Yin and Yang corner lines: Yang corner lines are also called Yang corner strips, which are decorative lines used for 90-degree convex corner wrapping of tiles. It is made of PVC, stainless steel, aluminum alloy, etc. , take the bottom plate as the surface, and one side is a 90-degree fan-shaped arc surface.

An outside corner is a raised corner formed by two walls in a house, which is almost inevitable in renovations. But I often hear people say that the tile corners of the house cracked and broke and collapsed soon after. I believe that many people will encounter this situation, and the paving of the sun angle is indeed a high incidence period of "accidents" in tile construction.

This article will dig deep into the treatment method of the outside corner of the ceramic tile to completely solve this problem. This article solves the following problems for you:

1. How should the chamfering of the tiles be achieved?

2. Is there any solution other than chamfering?

Realization of tile chamfering

When attaching wall tiles, in order to make the outer corners of the tiles fit more closely and beautifully, the most commonly used method is "chamfering", which is divided into fitting corners and Begonia corners.

1. Close-fitting corner

Sand the edges of the tiles neatly to a 45-degree angle, and then splicing, leaving no gaps or small gaps between the tiles. But the expansion coefficient of tiles is much smaller than that of reinforced concrete. During thermal expansion and contraction, if there is no gap or the gap is too small, the tile expands too slowly, which will cause cracking.

2. Begonia Cape

Grinding the edge of the tile to a 45° angle, but not grinding to the end will retain a certain side edge, increasing the side edge area, which can alleviate the side edge collapse, but it will cause the side edge to be exposed and affect the appearance.

Special treatment method of ceramic tile outside corner

Sun angle strips can be used.

In terms of shape, there are curved and U-shaped corner bars; in terms of material, there are stainless steel, ceramics, and aluminum alloys. At present, U-shaped stainless steel rods are widely used in the market. This type of rib is embedded in the tile and is not easy to fall off.

corner guard

According to the material, it is divided into metal corner protector, PVC plastic corner protector, winged corner protector, and wingless corner protector.

Advantages of corner guards

The corner protector has the advantages of corrosion resistance, impact resistance, aging resistance, good adhesion, and full integration with ceramic tiles, which greatly enhances the impact resistance of the corner, and keeps the corner beautiful and not damaged for a long time.

Construction is convenient. It can be constructed synchronously with the main project, and no ruler board is required during use. The operation is simple, and the construction efficiency is 2-5 times of the general one.

Corner guards are relatively cheap, saving construction costs.

Installation and construction method of corner guard

Treat the wall ahead of time. Make a mark on the wall as required, stick 2mm thick double-sided tape on both ends of the back of the corner protector, press the alignment mark firmly on the wall, let the double-sided tape fully touch the wall, and then let go.

Adhesive materials such as scotch tape or masking paper cannot be pasted on the surface of the corner guard, and will react with the paint on the surface, tarnish or peel off the paint.

Pay attention to the control and handling of the lines. Using decorative corner guards to assist construction, corner construction no longer requires rulers, the traditional and cumbersome construction technology has become very simple and easy to operate, and ordinary coolies can also master it, and can also make perfect corner straight lines.

Fixed corner guards. Stick the corner guard against the corner, align it horizontally or vertically, and then scrape off the overflowing grout; after drying, stick to the positioning edge on the top of the corner guard, and then scrape a layer of putty to level it.

ABOUT US

BEAUTRIM was founded in 2002 and spacialize in producing building decorative products.Since its inception oriented manufacturing PVC profiles for curtain track,decoration and furniture.Then introduced increasing the range of aluminum products year after year.

In therecently years,new materials such as stainless steel, brass were introduced into our production line,weadopted new technology to produce kinds of profiles and developed many different finishes for stainless steel & brass profiles,we are sure these new products would be more and more popular in the world near future.

Today BEAUTRIM products exported to many countries in Europe,North&South America,Africa etc,BEAUTRIM is distinguished from its competitors by marketing positioning,we are the most windest production line,and we always try to provide best quality-price products and professional service to our customers at the field of construction.

We thank the trust that customers and suppliers have placed in BEAUTRIM and its products year after year,we believe that we must have a bright future in the field construction.

CERTIFICATE

PACKING &SHIPPING

by sea & by air, 25-30 days deliver time, stick protective film for each pcs.including stick lable. 20 pcs/ctn, 40 pcs/ctn, 60 pcs/ctn and 100 pcs/ctn all can.

FAQ 

Q1:Are you a factory or a trading company?

A:Factory.

Q2:Where is your factory?

A:Ningbo, Zhejiang,China.

Q3:Are custom services available?

A:Yes.

Q4:Do you support OEM and ODM?

A:Yes.

Q5:Why choose us?

A:Our company has a professional R & D and design team,and we have rich experience in product production,Leading position in the industry.

Q6:Does your packaging ensure product safety?

A:We ship the profiles on pallets, which is very safe.

Q7:What information do I need to provide to get an accurate quote?

A:Material, thickness,weight for pcs finish & quantity etc.

Q8:How can I get product progress without going to your company?

A:Provide photos and videos in the production workshop.

Q9:How is your after-sales service?

A:According to the requirements of customers, try to meet them within the scope that can be achieved.

Q10:Can samples be ordered?

A:yes,can.

Q11:How much is the sample fee, can it be refunded after bulk product?

A:free samples.

Q12:Do you provide quality assurance?

A:yes.