Stainless Steel Internal

Description

Stainless steel closing method, understand the closing design.

Floor tiles and wooden floors, wallpaper and latex paint, the interface between the ground and the wall, the edge between the cabinet and the wall, the interface between the ceiling and the wall, etc., whether it is the same material or different materials or different planes, all need to use to the process of closing.

The closing method may not determine the quality of the design, but a poor closing will definitely affect the overall design.

Generally speaking, there are three main closing methods used in decoration, such as edge pressing, leaving seam, and collision.

Edge pressing is the most used method in the whole decorative closing, because it is simple in construction, low in cost and beautiful in effect. Decorative strips that do not conform to the atmosphere of the space will destroy the overall beauty. It is very important to choose a suitable and beautiful decorative strip.

Parts such as dividing strips, edge blanking strips, sheath lines, corner protection lines, decorative strips, etc. are all common edge blanking materials. Edge strips and decorative strips are the most popular closing materials at present, because they are suitable for the widest and most beautiful scenes, and can meet various closing needs, whether it is the ground, the wall, or between the ground and the wall, or even the top surface. It can be used with the closing treatment of wall materials.

The most commonly used parts of edge pressing are shown in the figure above, and their usage forms are similar. After understanding this principle, and looking at more beading cases, there are logic and rules to be found.

The seam closing method is to leave a gap of a certain width between adjacent materials or components for closing.

Harder materials, especially when they are bulky, can be difficult to keep seams tight with close seam closures. Therefore, materials with hard texture and large specifications, such as stone, glass, etc., are usually closed by leaving seams. When the material specification is small, the use of seam closing can make the finish look neat and beautiful, but it will increase the construction cost.

The processing method of leaving the seam is to leave a gap between the material and the material to transition, which not only plays the role of functional material buffering, but also achieves visual beauty and delicacy; it is especially suitable for the division of large decorative surfaces, two Plane docking of various materials, treatment of expansion joints in space, and effective means to increase the sense of hierarchy in space.

Whether or not to leave seams is generally determined by the designer's design requirements and style. If the material specification error is large, appropriate gaps can be left to avoid accumulated errors. The size of the closing joint is determined according to the size of the material, and after the construction is completed, the jointing treatment is carried out with cement, etc.

The bump-to-mouth method is often used in the closure of wood veneer materials or stone walls. The method is usually to plan the butt-jointed edges of wooden components into a bevel at a certain angle, and then overlap each other.

The wood veneer bumping port generally appears in the overlapping position of large-area wood veneer, external angle wood veneer, etc.

Some of the commonly used closing methods for design and decoration introduced above should be flexibly applied in actual design and construction according to the requirements of design effect and construction cost control.

Because of the same closing position, different closing methods may also achieve the same closing effect, and the same closing method may also produce different decorative effects due to different treatment of details.

The main purpose of closing the mouth is to decorate the transition part to enhance the effect of the decoration and achieve the effect of lifting a thousand pounds. However, in this process, the rabbit will always encounter the problem of closing the open corners, which makes the natural transition difficult to achieve.

When encountering the unavoidable opening of the outer corner, it is best to find a way to turn the outer corner into a flat or an inner corner. Because the inner corner is visually a depression, and the closure falls in the shadow, the blemish at the junction will become less obvious, and it is not easy to be impacted by external forces, making it safer.

At present, the popular tile trims on the market are mainly metal and plastic materials. Metal trims are generally made of stainless steel, and the trims that are not made of steel have a bright appearance and are bright wall tiles. It is a good choice for edges. When purchasing metal edge trims, you should pay attention to the purity of stainless steel and avoid buying inferior stainless steel edge trims.

We sell a variety of different high-quality stainless steel trims, welcome to buy.

ABOUT US

BEAUTRIM was founded in 2002 and spacialize in producing building decorative products.Since its inception oriented manufacturing PVC profiles for curtain track,decoration and furniture.Then introduced increasing the range of aluminum products year after year.

In therecently years,new materials such as stainless steel, brass were introduced into our production line,weadopted new technology to produce kinds of profiles and developed many different finishes for stainless steel & brass profiles,we are sure these new products would be more and more popular in the world near future.

Today BEAUTRIM products exported to many countries in Europe,North&South America,Africa etc,BEAUTRIM is distinguished from its competitors by marketing positioning,we are the most windest production line,and we always try to provide best quality-price products and professional service to our customers at the field of construction.

We thank the trust that customers and suppliers have placed in BEAUTRIM and its products year after year,we believe that we must have a bright future in the field construction.

CERTIFICATE

PACKING &SHIPPING

by sea & by air, 25-30 days deliver time, stick protective film for each pcs.including stick lable. 20 pcs/ctn, 40 pcs/ctn, 60 pcs/ctn and 100 pcs/ctn all can.

FAQ 

Q1:Are you a factory or a trading company?

A:Factory.

Q2:Where is your factory?

A:Ningbo, Zhejiang,China.

Q3:Are custom services available?

A:Yes.

Q4:Do you support OEM and ODM?

A:Yes.

Q5:Why choose us?

A:Our company has a professional R & D and design team,and we have rich experience in product production,Leading position in the industry.

Q6:Does your packaging ensure product safety?

A:We ship the profiles on pallets, which is very safe.

Q7:What information do I need to provide to get an accurate quote?

A:Material, thickness,weight for pcs finish & quantity etc.

Q8:How can I get product progress without going to your company?

A:Provide photos and videos in the production workshop.

Q9:How is your after-sales service?

A:According to the requirements of customers, try to meet them within the scope that can be achieved.

Q10:Can samples be ordered?

A:yes,can.

Q11:How much is the sample fee, can it be refunded after bulk product?

A:free samples.

Q12:Do you provide quality assurance?

A:yes.